Saltar al contenido Saltar a navegación Saltar al pie de página
INDIAN MOTORCYCLE
CENTRO DE AYUDA
12/05/2024

2015+ Roadmaster Drive Belt Inspection and Tension Adjustment

Required Tools and Supplies
Marking ToolBelt Tension Tool or 10-Pound Weight27mm Crow Foot
6mm Allen Socket13mm Socket27mm Wrench
Torque WrenchRatchetShop Rags
Safety GlassesNitrile Gloves


For more information on tools, read the Tools and Fasteners Guide.

Always wear safety glasses and nitrile gloves when servicing your Indian Motorcycle. To inspect and adjust the drive belt tension on your Indian Roadmaster, follow these steps:

1. Park the bike on a flat, level surface and allow it to cool completely.

2. Remove the upper side covers by pulling the corners evenly straight outward to disengage each tab from the rubber grommets in the frame. 

3. Disconnect the saddlebag lock connector near the seat. 

4. Open the saddlebag and remove the two saddlebag fasteners with a 6mm Allen socket.

5. Tilt the saddlebag out and lift up to remove. 

6. Ensure the motorcycle is in NEUTRAL. 

7. Lift the motorcycle according to your Owner’s Manual guidelines and elevate the rear wheel. The motorcycle must be stable before proceeding. 

8. Inspect the drive belt for wear or damage. Refer to your Owner’s Manual for belt wear analysis. See your authorized Indian Motorcycle Dealer if replacement is needed.

9. Applying 10 pounds of force, check and record the belt deflection. Ensure the belt is dry before measuring.

  • Using the tire valve stem as a reference, measure at three additional points 90 degrees apart on the tire. The drive belt deflection at 10 pounds of force should be 34mm (1.3 inches) or 11 notches up the belt guard.
  • If adjustment is needed, rotate the wheel forward and mark the tightest measurement point on the tire for reference. 

10.  Also mark the current adjuster locations on both sides of the rear wheel for reference.

11. Place a rag against the exhaust to prevent scratching the paint. Loosen but do not remove the axle nut with a 27mm wrench.

12. Retighten the nut with a 27mm crowfoot wrench to the adjustment specification of 15 ft-lbs (20 Nm).

13. Use a 13mm socket to turn the right-side adjuster nut as needed to achieve proper belt tension. 

14. When the belt tension is correct, move to the left side to adjust the final belt alignment. 

15. Use only the left-side adjuster to make final adjustments for belt alignment. Ensure the axle is seated forward against axle adjusters. 

16. While rotating the wheel backward, tighten the left-side adjuster nut until the drive belt is centered in the driven pulley. Sprocket teeth should be visible on both sides of the drive belt. 

17. Once the desired setting is achieved, rotate the wheel forward and verify the sprocket teeth are still visible on both sides of the drive belt. 

18. If necessary, revert back to the initial settings and repeat this process as needed. 

19. Re-check drive belt tension to verify it is still within specification. Improper tension or alignment can cause driveline noise and damage the drive belt. 

20. Tighten the rear axle nut to the final specification of 65 ft-lbs (88 Nm).

21. Pump the rear brake pedal several times to reset brake pad distance. 

22. When the brake pedal is released, verify that the wheel rotates smoothly and freely, without drag. 

23. Safely lower your motorcycle to the ground. Refer to your Owner’s Manual for helpful hints and techniques.

24. Begin reinstalling the saddlebags by placing them on the muffler brackets. 

25. Reinstall the saddlebag fasteners. Torque to 18 ft-lbs (24 Nm).

26. Reconnect the electrical wiring, if necessary, and ensure the saddlebags are mounted properly. 

27. Align the three side panel grommets and reinstall each upper side panel.

For more information, see your authorized Indian Motorcycle Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.

YouTube® is a registered trademark of Google LLC

Unless noted, trademarks are the property of Indian Motorcycle International, LLC
© 2022 Indian Motorcycle International, LLC

Palabra (s) clave video , maintenance , belt , inspect , inspecting , adjust , adjusting , tension ,