|Required Tools and Supplies|
|Shop Rags||Pick and Flathead Screwdrivers|
|Adjustable Wrench||Moly Assembly Grease or All-Purpose Grease|
|12mm Crowfoot Wrench||10mm and 12mm Wrenches|
|5mm Allen Socket||10mm Socket|
|Safety Glasses||Nitrile Gloves|
To learn more about tools, read the Tools and Fasteners Guide.
Always wear safety glasses and nitrile gloves when servicing your Indian Motorcycle.
To properly maintain and adjust the clutch lever on your Indian Scout, Scout Sixty, Scout Bobber, Scout Bobber Twenty, Scout 100th Anniversary model or Scout Rogue, follow these steps:
1. Park the motorcycle on a flat, level surface and allow the vehicle to cool completely.
2. Inspect the entire length of the clutch cable for any damage to the external casing. Also inspect any exposed cable wire for fraying, kinks or corrosion. Replace any cables that are damaged, sticky or sluggish.
3. Move down to the cable connection near the primary cover and slide up the rubber protector boot.
4. Remove the jam nut with a 12mm socket and set aside.
5. Use an adjustable wrench to rotate the clutch shaft arm until the tension has been released from the cable. Rotate the cable barrel out of the clutch shaft arm and release the clutch shaft.
6. Pull the cable down and out of the mounting boss.
7. On the left handlebar, carefully remove the plastic cap from the pivot pin. Replace if any damage occurs.
8. Unscrew the bottom hinge nut with a 10mm socket.
9. Remove the pivot pin with a 5mm Allen socket.
10. Remove the clutch lever and rotate the cable barrel out of the lever.
11. Remove any old grease and dirt from the lever, housing, and cable ends.
12. Lubricate the clutch lever and pivot screw with moly assembly grease or all-purpose grease.
13. Also apply a thin coating of all-purpose grease to both clutch cable ends. DO NOT lubricate between the cable and sheath.
14. Reinstall the clutch cable into the lever housing.
15. Install the clutch lever into the handlebar and align the pivot pin hole.
16. Reinstall the pivot pin until fully seated.
17. Reinstall the nut. Torque to 35 to 62 in-lbs (4-7 Nm).
18. Reinstall the pivot pin cap.
19. Clean any residual grease off the handlebar.
20. Rotate the clutch shaft arm and reconnect the clutch cable into the lower cable housing.
21. Reinstall the jam nut. Torque to 48 in-lbs (5.4 Nm) with a 12mm crowfoot wrench.
22. Slide the rubber protector boot into place.
23. Ensure the cable is properly routed in the mounting boss and cable bracket.
24. Measure the clutch lever free play between the clutch lever and the clutch lever mounting bracket. The free play should be 0.5 to 1.55 mm (0.02 to 0.059 inches).
25. If adjustment is needed, the clutch cable adjuster nut is located along the lower right frame. While holding the clutch cable, slide the rubber protector boot away from the lock nut.
26. Loosen the lock nut with a 12mm wrench.
27. While holding the cable, use a 10mm wrench to turn the cable adjuster inward or outward until the clutch lever free play is set to specification.
28. While holding the adjuster, torque the adjuster lock nut to 48 in-lbs (5.4 Nm) with a 12mm crowfoot wrench.
29. Re-secure the protector boot over the adjuster.
30. Finish by verifying proper operation of the clutch. The engine should not start with the clutch lever released and the vehicle in gear. Repeat this procedure as needed.
For more information, see your authorized Indian Motorcycle Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.
YouTube® is a registered trademark of Google, Inc.
Unless noted, trademarks are the property of Indian Motorcycle International, LLC.
© 2022 Indian Motorcycle International, LLC