Skip to content Skip to navigation Skip to footer
INDIAN MOTORCYCLE
HELP CENTER
09/30/2024

2025 Indian Scout Oil and Filter Change

Required Tools and Supplies

  • 6mm Allen Socket
  • Oil Filter Wrench
  • Ratchet
  • Torque Wrench
  • Oil Pan
  • Funnel
  • Sealing Washers
  • Drain Plugs
  • Eye Protection
  • Nitrile Gloves
  • Shop Rags

For more information on tools, read the Tools and Fasteners Guide.

Always wear safety glasses and nitrile gloves when servicing your Indian Motorcycle. Change the engine oil at the intervals specified in the Periodic Maintenance Table found in your Owner's Manual. Change the oil more frequently if the motorcycle is subjected to severe use, especially operation in cold weather. Freezing condensation can result in plugged oil lines and serious engine damage. The oil change kit is part number 2884171. The kit includes four quarts of Indian Motorcycle Full Synthetic 15W-60 oil, one oil filter and two drain plug washers. Additional oil may be needed, it is recommended to keep additional oil on hand. A quart of oil is part number 2880187.

Due to the semi-active dry sump lubrication system, the engine oil level shown in the oil sight glass will fluctuate with movement of the motorcycle from a vertical position and with the temperature of the oil. To get an accurate reading, follow all inspection procedures closely.

The total amount of oil required for the oil and filter change is approximately 3.5 - 4 quarts (2.8 to 3.8 l). Follow all instructions carefully. Do not overfill.

Note: After an oil change, the low oil pressure indicator may illuminate when the engine is started. If this occurs, do not increase RPM above idle speed until the indicator turns off. Operating above idle speed could result in damage to the engine.

To perform an oil and filter change on your Indian Scout, follow these steps:

1. Park the motorcycle on a flat, level surface in a well-ventilated area. Note: For proper oil drain, use a service lift to ensure the motorcycle is vertically centered.

2. Start the engine and allow it to warm up at idle for at least 5 minutes. Caution: Oil level will NOT be accurate if checked on a cold engine. DO NOT ADD oil to raise level to the middle of the sight glass on a cold engine, as this can result in overfilling.

3. Stop the engine. 

4. Clean the area around the two drain plugs.

5. Place a drain pan under both drain plugs. Tip: Placing a rag in the bottom of the drain pan will help prevent the splashing of oil.

6. Remove the drain plugs and washers with a 6mm Allen Socket, and allow the oil to drain completely. Tip: Remove the front drain plug first.

7. Inspect the drain plugs. The sealing surfaces on the plugs and engine should be clean and free of burrs, nicks or scratches.

8. Install new sealing washers (part number 5812232) on the drain plugs (part number 7052306) and reinstall the drain plugs to specification. Torque: 15 ft-lbs (20 Nm)

9. Place a drain pan under the oil filter and turn the filter counter-clockwise with an Oil Filter Wrench to remove it.

10. Using a clean dry cloth, clean the filter sealing surface on the engine.

11. Lubricate the O-ring on the new oil filter (part number 2520799) with a film of fresh engine oil and ensure it is in good condition.

12. Install the new filter and rotate it clockwise by hand until the filter gasket contacts the sealing surface, then turn it an additional 3/4 to one full turn.

13. Wipe up any residual oil around the filter.

14. Use a funnel and add the initial amount of recommended oil (part number 2880187) through the engine oil fill port. The initial fill amount is 3.5 - 4 quarts (2.8 to 3.8 liters). Important: Total engine oil fill volume with oil filter change will be approximately 4.5 qt (4.25 L). Total engine oil fill volume with a new or rebuilt (dry) engine will be approximately 5.25 qt (4.96 L).

15. With the motorcycle in an upright, centered position, start the engine and allow it to idle for 30 seconds and then stop the engine.

16. Inspect the oil level by looking at the oil sight glass. The oil level should be at or near the full mark on the oil sight glass. If the oil level is low, remove the engine fill plug and add oil as needed. DO NOT OVERFILL. Then repeat the previous step. Note: After an oil change, the low oil pressure indicator may illuminate when the engine is started. If this occurs, do not increase the RPM above idle speed until the indicator turns off. 

17. Check for leaks around the drain plug and oil filter.

18. Navigate to the settings menu on your motorcycle and select OIL LIFE AND SERVICE RESET. 

19. Select the reset function and confirm your selection.

20. Dispose of the used oil and filter properly at your local recycling center.

For more information, see your authorized Indian Motorcycle Dealer. Find a dealer near you with the Dealer Locator. Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.

YouTube® is a registered trademark of Google LLC

Unless noted, trademarks are the property of Indian Motorcycle International, LLC
© 2024 Indian Motorcycle International, LLC